Products
  • RAN-H200 Series Rainproof LED Power Supply
  • RAN-H200 Series Rainproof LED Power Supply
  • RAN-H200 Series Rainproof LED Power Supply
  • RAN-H200 Series Rainproof LED Power Supply
  • RAN-H200 Series Rainproof LED Power Supply
  • RAN-H200 Series Rainproof LED Power Supply
  • RAN-H200 Series Rainproof LED Power Supply
  • RAN-H200 Series Rainproof LED Power Supply
  • RAN-H200 Series Rainproof LED Power Supply
  • RAN-H200 Series Rainproof LED Power Supply
  • RAN-H200 Series Rainproof LED Power Supply
  • RAN-H200 Series Rainproof LED Power Supply
RAN-H200 Series Rainproof LED Power Supply
  • Wide input voltage input;
  • Working temperature range -30℃~+50℃。
  • Withover current protection, over power protection, & short circuit protection
  • Installation Method:Vertical installation
  • 3-Years warranty
Model RAN-H200-V012
Input Voltage range 190V-250Vac
Input Current ≤2A(190-250Vac)
Efficiency ≥85%(Typ.)
Frequency Range 50 / 60HZ
Output Rated output voltage 12V
Rated current 16.6A
Voltage power 199.2W
Output Ripple & Noise ≤150mV 
Environment Condition Range of working temperature -30℃ ~50℃
Storage temperature -35℃ ~ 85℃
Storage Humidity 10~95%RH
Vibration 10~500HZ, 5G, 30 minutes(for X,Y, Z each axis)
IP Rating □IP23  □IP67  □IP68  □NO
Safety & EMC Safety Standard GB4943 / EN60950
Dielectric Strength (Hi-Pot) I/P-O/P 1.5KVAC/ 10mA/ 60S
I/P-FG 1.5 KVAC/ 10mA/ 60S
O/P-FG 0.5 KVAC/ 10mA/ 60S
Insulation Resistance 100MΩ Max/ 500VDC/ 3S
Grounding Resistance 100mΩ
EMC  GB17625.1-2003(idt IEC 61000-3-2:2001)
Reliability MTBF 25℃:100000Hrs,MIL-217 Method
Others Dimension 202*111.5*53.5(L*W*H)
Cooling method ◻️Ventilation Cooling  ◻️air cooling
Extension method ◻️Three-proofing lacquer  ◻️Stamped 
◻️Low temperature start-up(-40℃)◻️Others
Note *Unless otherwise specified, all specifications are measured at an input of 230VAC, rated load, 25°C.
*In order to extend the service life, it is recommended to leave an additional 30% margin when configuring the load. For example, if the device requires 100W of power, the power supply of not less than 130W is selected.
* Switching power supply ripple test method: test on the power supply output terminal with a 20MHz oscilloscope, the ground length of the oscilloscope probe is not more than 12mm, and the probe input is paralleled with 47uF electrolytic capacitors and 0.1uF high frequency capacitors.
*The power supply is part of the equipment system components, and all EMC tests need to be confirmed in conjunction with the end equipment for electromagnetic compatibility.
Inquiry

+8675523208269

jack_xu@leadpowers.com

https://www.leadpowers.com

+8675523208269

Unit 401-403,Block 5B,Skyworth Innovation Valley,Tangtou 1st Road ,Shiyan Street,Bao'an District, Shenzhen,China

CONTACT US
  • Name*

  • E-Mail*

  • Write Your Message*

  • Code*

  • SEND
Copyright ® Shenzhen LeadPower Technology Co., Ltd. All Rights Reserved