| Model | RAP-K400-V012P | ||||
| Input | Voltage range | 90~264VDC | |||
| Max Input current | 5A/176VAC， | ||||
| Frequency Range | 47~63Hz | ||||
| PF | PF≥0.95/100～240Vac | ||||
| Inrush current | ≤90A | ||||
| Output | DC voltage | 12V | |||
| Output Voltage Range Under Constant Current Area |
10.8~13.2 VDC | ||||
| Rated current | 15A | 90~200Vac input | |||
| 27A | 200~264Vac input | ||||
| Output power | 360W | ||||
| Efficiency | ≥88%(Typ.90%) | ||||
| Ripple & noise | 150mVp-p | ||||
| Output Voltage Rise time | 100ms | ||||
| Dynamic Response Overshoot | 5% | ||||
| Dynamic Response Recovery Time | 300μs | ||||
| Turn-on delay time | 3s | ||||
| Line regulation | ±1% | ||||
| Load regulation | 2% | ||||
| Voltage tolerance | ≤±4% | ||||
| Environment condictions | Range of working temperature | -30~60°C(refer to derating curve for details) | |||
| Storage temperature | -40~80℃ 5%~95%RH Non-condensing | ||||
| Atmosphere Pressure | 70～106Kpa | ||||
| Altitude | 5000mtrs (Altitude over 2000 meters, the load is derated by 1.5% for every 100 meters.) | ||||
| EMC& Safety | Dielectric Strength | Input To Output | 3000Vac/10mA/1min | No arc, no breakdown | |
| Input To FG | 1500Vac/10mA/1min | ||||
| Output To FG | 500Vac/10mA/ 1min |
||||
| Insulation Resistance | Input To Output | ≥10MΩ@ 500Vdc | 90%RH, 1 atm | ||
| Input To FG | ≥10MΩ@ 500Vdc | ||||
| Output To FG | ≥10MΩ@ 500Vdc | ||||
| Leakage Current | Input To FG | ≤3.5mA | 240Vac/60Hz | ||
| Input To Output | ≤0.7mA | ||||
| Safety Standards | he design conforms to UL60950, IEC/EN60950, GB4943.1-2011 standard requirements |
||||
| EMI | EN55015 | ||||
| EMS | En61000-4-2,3,4,5,6,8,11, EN55024 Standard for Light industry Class A (surge 4 kV) criteria B |
||||
| Protection | Over Voltage protection | 13.8~16.2V | |||
| current-limiting protection | 35~43A | ||||
| Short circuit protection | It can be short circuited for a long time without damage. After the short circuit fault is removed, restarting the power supply is needed. |
||||
| Reliability | MTBF | 25°C environmen：150000Hrs，MIL-217 Method | |||
| Others | Dimension | 235*115*42mm（L*W*H） | |||
| Cooling method | √Ventilation cooling Air cooling | ||||
| Extension method | Three-proofing lacquer Stamped Low temperature start-up（-40℃） Others |
||||
| Note | *Unless otherwise specified, all specifications are measured at an input of 230VAC, rated load, 25°C. *In order to extend the service life, it is recommended to leave an additional 30% margin when configuring the load. For example, if the device requires 100W of power, the power supply of not less than 130W is selected. * Switching power supply ripple test method: test on the power supply output terminal with a 20MHz oscilloscope, the ground length of the oscilloscope probe is not more than 12mm, and the probe input is paralleled with 47uF electrolytic capacitors and 0.1uF high frequency capacitors. *The power supply is part of the equipment system components, and all EMC tests need to be confirmed in conjunction with the end equipment for electromagnetic compatibility. |
||||
+8675523208269
jack_xu@leadpowers.com
https://www.leadpowers.com
+8675523208269
Unit 401-403,Block 5B,Skyworth Innovation Valley,Tangtou 1st Road ,Shiyan Street,Bao'an District, Shenzhen,China
